Workshop manuals for agricultural & construction machinery

Trusted Since 1995
Digital PDF manuals • Worldwide service

Allison Transmission 1000 Series, 2000 Series, 2000 MH Series, 2400 Series Mechanics Tips – Pub No. MT3190EN — SKU: Allison Transmission 8

£24.00

Allison Transmission 1000 2000 Mechanics Tips is a 58-page digital PDF reference covering preventive maintenance, fluid and filter service, transmission removal, installation preparation, vehicle adaptation checks and fitting procedures for Allison vocational transmission families.

Description

Allison Transmission 1000 2000 Mechanics Tips is a practical workshop reference for preventive maintenance, transmission removal, installation preparation, vehicle adaptation checks and customer service information for the listed Allison vocational transmission families.

WHAT THIS MANUAL CONTAINS

  • Section I – Preventive Maintenance – Covers the routine care work required to keep the transmission serviceable, beginning with periodic inspections and care for the transmission and associated installation points.
  • Importance of Proper Transmission Fluid Level – Explains why the correct fluid level matters and why fluid level must be checked carefully before the transmission is operated or assessed.
  • Transmission Fluid Check – Gives the fluid-check procedure, including the conditions and checks used for accurate cold and hot fluid-level assessment.
  • Keeping Fluid Clean – Deals with contamination prevention and the need to protect the transmission fluid during servicing, inspection and refill work.
  • Fluid Recommendations – Identifies the recommended fluid information, including DEXRON and TranSynd considerations and operating-temperature requirements.
  • Transmission Fluid and Filter Change Intervals – Provides the maintenance interval guidance for fluid and filter changes, with schedules related to vocation, operating severity and fluid type.
  • Transmission Fluid Contamination – Addresses contamination conditions, the effect of contaminated fluid and the checks required when fluid condition is suspect.
  • Transmission Fluid and Filter Change Procedure – Sets out the service sequence for draining, changing the applicable filters, refilling and checking the transmission after maintenance.
  • Oil Vent (Breather) – Covers inspection and care of the transmission oil vent or breather as part of preventive maintenance.
  • Section II – Removing Transmission – Provides the removal sequence for taking an Allison transmission out of the vehicle while protecting the transmission, driveline and connected controls.
  • Draining Transmission – Describes draining the transmission fluid and dealing with fluid remaining in connected cooler and transmission areas before removal.
  • Disconnecting Controls – Covers disconnecting the transmission controls, electrical connections and other control-related connections before the unit is separated from the vehicle.
  • Uncoupling from Driveline, Engine and Vehicle – Explains the separation of the transmission from the driveline, engine and vehicle mounting arrangement.
  • Removing the Transmission – Gives the practical removal steps, including support, clearance and handling considerations for taking the unit from the vehicle.
  • Removing the Flexplate Adapter – Covers removal of the flexplate adapter where fitted and the related engine-to-transmission connection.
  • Removing Output Flange or Yoke – Describes removal of the output flange or yoke before installation preparation or component transfer.
  • Section III – Preparing the Transmission for Installation – Covers the checks and component preparation required before the transmission is returned to the vehicle.
  • Checking Input Components – Includes inspection of the input-side components and mating parts before installation.
  • Installing Output Flange or Yoke – Provides the installation considerations for the output flange or yoke and its connection to the driveline.
  • Installing PTO – Covers preparation and installation of the power take-off where the vehicle specification includes a PTO.
  • Installing Fill Tube and Seal – Deals with fitting the transmission fill tube and seal so the fluid filling and checking arrangement is correctly restored.
  • Checking Plugs and Openings – Lists the checks for plugs, openings and unused connection points before the transmission is installed.
  • Section IV – Preparing Vehicle for Transmission Installation – Covers the vehicle-side inspections and dimensional checks needed before the replacement or serviced transmission is mounted.
  • Engine-to-Transmission Adaptation Requirements – Includes flywheel housing pilot-bore checks, bore runout, face squareness and crankshaft hub pilot inspection.
  • Checking Flexplate Drive Assembly – Covers inspection of the flexplate drive assembly and its suitability for the transmission and engine combination.
  • Chassis and Driveline Inspection – Deals with checking the chassis, driveline alignment and related vehicle components before installation.
  • Cooler, Filter and Lines – Includes inspection and preparation of the transmission cooler, filter arrangement and connecting lines.
  • Checking Controls – Covers inspection of the vehicle controls and associated control connections before the transmission is fitted.
  • Section V – Installing Transmission into Vehicle – Gives the installation sequence for positioning, mounting, connecting and commissioning the transmission in the vehicle.
  • Handling and Mounting to Engine – Covers safe handling and the procedure for bringing the transmission into position and attaching it to the engine.
  • Installing Mounting Components – Describes fitting the transmission mounting components and securing the unit in the vehicle.
  • Coupling to Driveline – Covers reconnection to the driveline and the related alignment and fastening work.
  • Connecting PTO Controls – Provides the connection information for PTO controls where fitted.
  • Connecting Parking Brake Control – Covers reconnection of the parking-brake control arrangement.
  • Connecting Cooler – Describes reconnecting the cooler and related fluid lines after the transmission has been mounted.
  • Connecting Controls – Covers reconnection of the transmission controls, electrical leads, speed sensors, PTO connector and other applicable connectors.
  • Filling Hydraulic System – Includes refilling the transmission hydraulic system and the final fluid-level and operational checks following installation.
  • Section VI – Customer Service – Provides owner-assistance information and identifies related Allison service literature for further operation, maintenance, service, overhaul, parts and troubleshooting support.

MODELS COVERED

Allison 1000 Series, 2000 Series, 2000 MH Series and 2400 Series vocational transmissions, including 1000 EVS, HS, MH, PTS, RDS and SP; 2100 EVS, HS, MH, PTS, RDS and SP; 2200 EVS, HS, MH, PTS, RDS and SP; 2500 EVS, HS, MH, PTS, RDS and SP; plus B 210 and B 220 bus models.

HOW THIS MANUAL HELPS

Allison Transmission 1000 2000 Mechanics Tips gives technicians a structured reference for routine transmission care and vehicle-level service work. It helps organise fluid and filter maintenance, removal preparation, dimensional checks and reinstallation tasks. The manual is suited to workshop use when servicing the listed vocational transmission families. Use it alongside the vehicle manufacturer’s information and applicable safety procedures.

For maintenance work, Allison Transmission 1000 2000 Mechanics Tips brings the relevant fluid checks, contamination precautions, service intervals and breather care into one reference. For removal work, it follows the main connections and separation points in sequence. For installation work, it covers transmission preparation, engine adaptation, chassis checks, cooler connections, controls and hydraulic-system filling. This makes it useful when planning or checking a transmission replacement or installation.

The maintenance section includes periodic inspection, fluid-level checking, fluid recommendations, contamination, filter changes and oil-vent care. The removal section covers draining, control disconnection, driveline and engine uncoupling, flexplate adapter removal and output flange or yoke removal. The installation sections then address input components, PTO fitting, fill-tube sealing, flywheel housing measurements, flexplate inspection, driveline and cooler preparation, control connections and final filling.

Allison Transmission 1000 2000 Mechanics Tips – MANUAL DETAILS

  • Maker: Allison Transmission
  • Models: 1000 Series, 2000 Series, 2000 MH Series, 2400 Series, including the listed vocational models and B 210/B 220
  • Machine type: Automatic transmissions
  • Manual type: Mechanics Tips workshop reference
  • Format: Digital PDF
  • Publication number: MT3190EN
  • Page count: 58 pages
  • Year: 2000

Browse all Allison Transmission manuals available from Agrimanual.

WHAT HAPPENS AFTER PURCHASE?

After purchase you will receive our download information file by email straight away; it explains how delivery works. Your manual will then be manually checked and sent to the email address used during checkout, normally within 1 to 2 hours and always within 24 hours.

WHY BUY FROM AGRIMANUAL?

  • Established in 1995 supplying technical manuals
  • Digital PDF manuals for agricultural and construction machinery
  • Large archive including rare and discontinued manuals
  • Worldwide service
  • Manual orders checked before delivery

Allison Transmission 1000 2000 Mechanics Tips