Workshop manuals for agricultural & construction machinery

Trusted Since 1995
Digital PDF manuals • Worldwide service

Allison 4000 & B 500 Product Families Inspection and Analysis Technicians’ Guide – Pub No. GN4065EN — SKU: Allison Transmission 3

£24.00

The Allison 4000 B500 Guide is a digital PDF technicians’ guide for inspection and analysis of Allison 4000 and B 500 product families. It covers component identification, inspection guidelines, dimensional limits, supersession information, clutch and planetary modules, torque converters, control components and spring data.

Description

Allison 4000 B500 Guide provides technician-focused inspection and analysis information for Allison 4000 and B 500 product families, including component identification, inspection criteria, wear limits, supersession details and spring data.

WHAT THIS MANUAL CONTAINS

  • Glossary of Terms – terminology used throughout the inspection and analysis procedures for Allison 4000 and B 500 transmissions.
  • Introduction to Inspection and Analysis – purpose of the guide, technician use, inspection approach and relationship to diagnosis and repair work.
  • General Inspection Guidelines for Cast Parts and Machined Surfaces – inspection of housings, mounting faces, bores, fluid passages, lands, cracks, porosity, damaged surfaces and Spiralock threaded holes.
  • General Inspection Guidelines for Gears – examination of gear teeth, tooth surfaces, wear, damage and conditions affecting continued reuse.
  • General Inspection Guidelines for Splines – identification of spline wear, damaged teeth, worn shafts and related reuse or replacement considerations.
  • General Inspection Guidelines for Friction Plates – inspection of friction surfaces, spline condition, plate thickness, coning and identification of former and current friction plate designs.
  • General Inspection Guidelines for Reaction Plates – checking reaction plates, backing plates, return plates, distortion, wear, thickness and serviceability.
  • General Inspection Guidelines for Bearings and Bushings – inspection of bearing and bushing condition, wear and dimensional limits used during component analysis.
  • General Inspection Guidelines for Springs – checking springs for cracks, breakage, permanent set, identification characteristics and load-versus-height requirements.
  • General Inspection Guidelines for Seals and Sealrings – examination of sealing components, wear, damage and conditions that may affect fluid retention.
  • General Inspection Guidelines for Fluid – inspection considerations for transmission fluid condition and contamination during component analysis.
  • Control Module – identification and inspection of the main valve body, converter regulator valve, main regulator valve, lube regulator valve, lockup valve, C1 and C2 latch valves, exhaust backfill valve, springs, stops and solenoid details.
  • Torque Converter Module – converter pump identification, front cover markings, converter paint-dot colours, engraved and stamped identifiers, stator blade counts, mounting faces, pilots, end plugs, turbine shafts, damper components and clutch plate inspection.
  • Standard Rear Cover and P3 Planetary Module – inspection of the rear cover, P1 carrier, P2 and P3 planetary components, ring gears, indexing rings, pinion gears, spindles, roller bearings, thrust washers and retaining rings.
  • Rotating Clutch Module – identification and inspection of rotating clutch components, C1 drive hub, piston, backing plate, apply plate, clutch pack, return plate, spring assembly, thrust bearings and related oil passages.
  • C3/C4 Clutch Module – examination of C3 and C4 friction plates, piston return plates, spring assemblies, P1 ring gear, clutch housings, backplates, apply components and component-mixing restrictions.
  • Supersession Information – identification of design changes affecting converter regulator valve stops, turbine shafts, rotating clutch hubs, C5 friction plates, P3 ring gears and C3/C4 return plate and spring assemblies.
  • Inspection Criteria and Dimensional Data – component reuse limits, minimum thicknesses, maximum distortion, spline wear, pilot dimensions, bearing and bushing limits and other inspection measurements.
  • Spring Data – spring part numbers, colour codes, foldout references, wire dimensions, coil counts, free lengths, loaded lengths and load values for control and clutch components.
  • Foldout References and Notes – illustrated component references supporting inspection, identification and comparison of assemblies throughout the guide.

MODELS COVERED

Allison 4000 product family and B 500 product family transmissions.

Allison 4000 B500 Guide – MANUAL DETAILS

  • Maker: Allison Transmission
  • Models: 4000 product family; B 500 product family
  • Machine type: Automatic transmission
  • Manual type: Technicians’ guide for inspection and analysis
  • Format: Digital PDF
  • Publication number: GN4065EN
  • Page count: 82 pages
  • Publication date: May 2005

HOW THIS MANUAL HELPS

This Allison 4000 B500 Guide supports technicians when examining transmission components during diagnosis, overhaul and repair preparation. It brings inspection guidance, component identification and dimensional criteria together for the 4000 and B 500 product families.

The Allison 4000 B500 Guide can help with decisions about component condition, reuse, replacement and design changes. Its module-based layout provides a practical reference when checking valve-body parts, torque-converter components, planetary assemblies, clutch packs and springs.

Use the Allison 4000 B500 Guide alongside the applicable service procedures and parts information for the specific transmission assembly being worked on.

Browse all Allison Transmission manuals available from Agrimanual.

WHAT HAPPENS AFTER PURCHASE?

After purchase you will receive our download information file by email straight away; it explains how delivery works. Your manual will then be manually checked and sent to the email address used during checkout, normally within 1 to 2 hours and always within 24 hours.

WHY BUY FROM AGRIMANUAL?

  • Established in 1995 supplying technical manuals
  • Digital PDF manuals for agricultural and construction machinery
  • Large archive including rare and discontinued manuals
  • Worldwide service
  • Manual orders checked before delivery

Allison 4000 B500 Guide