Workshop manuals for agricultural & construction machinery

Trusted Since 1995
Digital PDF manuals • Worldwide service

Allison Transmission 1000 & 2000 Inspection and Analysis Technicians’ Guide – Pub No. GN4062EN — SKU: Allison Transmission 1

£19.00

The Allison 1000 2000 inspection analysis manual provides focused inspection guidance for transmission overhaul work, covering gears, bearings, clutch plates, valve bodies, solenoids, torque converters, shafts, planetary assemblies, clutch packs, sensors, the NSBU switch, wear limits and spring data.

Description

Allison 1000 2000 inspection analysis manual for technicians assessing transmission components, serviceability, wear, damage, reuse and replacement during overhaul work on Allison 1000 and 2000 Product Family transmissions.

WHAT THIS MANUAL CONTAINS

  • Glossary of Terms – Definitions used throughout the guide, including abrasion, battering, brinelling, galling, grooves, inadequate condition, light stoning and related inspection terminology.
  • Introduction to Inspection and Analysis – Purpose of the technician’s guide, its use alongside the 1000 and 2000 Product Families Service Manual, and the inspection approach used to determine whether transmission parts are serviceable and suitable for reuse.
  • General Inspection Guidelines for Cast Parts and Machined Surfaces – Inspection of housings and machined surfaces, including damage, surface condition, repairable irregularities and replacement considerations.
  • General Inspection Guidelines for Gears – Examination of gear teeth and thrust-face surfaces for damaged, broken or missing teeth, changed tooth shape, wear and defects that may require light stoning or replacement.
  • General Inspection Guidelines for Splines – Inspection of splined parts for burrs, damage, battered areas and excessive wear affecting component serviceability.
  • General Inspection Guidelines for Bearings – Inspection of ball bearings, bearing races and retainers, with attention to wear, damage, roughness and other conditions affecting reuse.
  • General Inspection Guidelines for Retaining Rings – Checking retaining rings for damage, distortion and excessive wear, including conditions that may be corrected with a soft stone or crocus cloth.
  • General Inspection Guidelines for Thrust Washers – Assessment of worn, galled, abraded or distorted thrust washers, including damage caused by inadequate lubrication and replacement requirements.
  • General Inspection Guidelines for Clutch Plates – Inspection of contact surfaces, plate thickness, coning, oil-groove depth, spline teeth, tangs, scoring, discolouration and driveline-related wear indications.
  • General Inspection Guidelines for Springs – Examination of springs for breakage, cracking, permanent set and rubbing wear, with reference to the Service Manual spring data charts for identification and specifications.
  • Control Valve Body Assembly – Identification and inspection of the main valve body, shift valve bodies, separator plate, solenoids, pressure switch manifold, valves, valve bores, oil passages, retainers, pins, springs and related components.
  • Control Valve Body Assembly: Valve and Bore Inspection – Checking valves and bores for nicks, burrs, scoring and sticking, while identifying when slight irregularities may be treated with a soft stone or crocus cloth and when replacement is required.
  • Control Valve Body Assembly: Solenoids and Pressure Switches – Identification of A, B, C, D, E, F and G solenoids, pressure switches, solenoid resistance considerations, visible damage, contamination by water or antifreeze and reference to troubleshooting procedures.
  • Control Valve Body Assembly: Internal Wiring and Oil Passages – Inspection of wiring harness connectors, terminals, protective coverings, retainers, O-rings, separator plates, signal tubes and the identified control-main oil passages.
  • Control Valve Body Assembly: Supersession Information – Component and calibration update references relating to TCM and calibration changes for the 1000 and 2000 Product Families.
  • Torque Converter – Inspection of the converter exterior, ribs, stator, hub, pilot and endplay, including checks for impact damage, discolouration, leakage, correct stator locking and freewheeling action.
  • Torque Converter Housing – Examination of the housing, machined mounting and sealing surfaces, cooler ports, filter and pressure attachment threads, tube connections and identified main oil passages.
  • Rear Cover Assembly – Component identification and inspection guidance for the rear cover assembly and its relevant machined, sealing and supporting surfaces.
  • Main Shaft Assembly – Inspection of the main shaft assembly, including component condition, bearing and surface areas, splines, grooves and other features affecting serviceability.
  • P1 Planetary and P2 Ring Gear – Examination of the planetary and ring-gear components, including gear teeth, thrust surfaces, splines and wear-related conditions.
  • P2 Planetary and P3 Ring Gear – Inspection of the P2 planetary and P3 ring gear components for damage, wear, surface defects and conditions affecting reuse.
  • P3 Planetary Assembly – Identification and inspection of the P3 planetary assembly and its associated gear, bearing, thrust and rotating surfaces.
  • Output Shaft – Inspection of the output shaft, including shaft surfaces, splines, bearing areas and other wear or damage points relevant to serviceability.
  • Front Support and Charging Oil Pump Module – Identification and inspection of the front support and charging oil pump module, including machined surfaces, pump-related areas and oil passages.
  • Rotating Clutch Housing – Inspection of the rotating clutch housing, including its gear, mounting, spline, bearing and component-contact areas.
  • Turbine Shaft – Examination of bushing and bearing journals, lubrication oil passages, seal-ring grooves, splines, snap-ring grooves and related wear surfaces, with supersession information where provided.
  • C1 Clutch Pack Components – Inspection of the C1 clutch pack, backplate, drive housing, piston hub, thrust bearing and associated clutch-contact surfaces.
  • C2 Clutch Pack Components – Identification and inspection of C2 clutch pack components, including plate, housing, piston, bearing and related wear areas.
  • C3 and C4 Clutch Pack Components – Inspection of the C3 and C4 clutch pack components, including plates, backing and reaction parts, splines, contact faces and damage affecting reuse.
  • Main Housing – Inspection of the main housing, machined surfaces, bores, sealing areas, passages, threaded features and other structural or serviceability concerns.
  • C5 Clutch Pack Components – Examination of C5 clutch pack parts, including friction and steel plates, housing, piston, backing components, splines and thrust areas.
  • Park Pawl Components – Inspection of park pawl components, engagement parts, contact surfaces, retainers and return components for wear, damage and correct condition.
  • Speed Sensors – Identification and inspection of speed sensor components and related mounting or signal-generating features.
  • Neutral Start Backup (NSBU) Switch – Identification of earlier and current switch designs, connector arrangements, switch body, connector, splash shield and retainer, together with supersession information.
  • Wear Limits and Spring Data – Reference tables for applicable wear limits, spring identification, part numbers, dimensions and spring data used during inspection and overhaul assessment.
  • General Inspection Guidelines for Torque Converter Module – Additional inspection reference material for the torque converter module and associated assessment points.

MODELS COVERED

Allison 1000 Product Family transmissions and Allison 2000 Product Family transmissions.

HOW THIS MANUAL HELPS

This technician’s guide supports overhaul inspection of Allison 1000 and 2000 Product Family transmission parts. It helps a skilled technician identify component features, assess wear and damage, and decide whether parts are suitable for repair, reuse or replacement. Use it together with the applicable Allison service and troubleshooting manuals when carrying out transmission work.

Allison 1000 2000 inspection analysis manual – MANUAL DETAILS

  • Maker: Allison Transmission
  • Models: Allison 1000 and 2000 Product Families
  • Machine type: Automatic transmission
  • Manual type: Technicians’ inspection and analysis guide
  • Format: Digital PDF
  • Publication number: GN4062EN
  • Page count: 66 pages
  • Year: 2000

Browse all Allison Transmission manuals available from Agrimanual.

WHAT HAPPENS AFTER PURCHASE?

After purchase you will receive our download information file by email straight away; it explains how delivery works. Your manual will then be manually checked and sent to the email address used during checkout, normally within 1 to 2 hours and always within 24 hours.

WHY BUY FROM AGRIMANUAL?

  • Established in 1995 supplying technical manuals
  • Digital PDF manuals for agricultural and construction machinery
  • Large archive including rare and discontinued manuals
  • Worldwide service
  • Manual orders checked before delivery