Description
Claas Targo K50 Workshop Manual is a 252-page digital workshop repair manual for CLAAS Targo K50, K60 and K70 telescopic handlers. Publication 349865.0, dated August 2003, is arranged for workshop-level servicing, fault investigation, component removal and refitting, dismantling, inspection and assembly of the principal machine systems.
The manual is intended for trained and suitably equipped technicians. It combines illustrated procedures with technical data, adjustment and pressure-check information, system descriptions, wiring-related transmission-control checks and machine specifications. It is particularly useful where repairs involve the axles, steering, brakes, engine installation, Dana T12000 powershift transmission, boom or cab/chassis equipment.
WHAT THIS MANUAL CONTAINS
- Introduction, machine identification and workshop safety – general manual information, identification guidance, health and safety requirements, and precautions for repair work.
- Front and rear axles – axle descriptions, removal and installation procedures, servicing instructions and axle-component repair.
- Steering system – steering-cylinder removal and overhaul, steering-system checking, steering-valve removal and dismantling procedures.
- Planetary hub and wheel-end repairs – epicyclic reduction gears, wheel hubs, kingpin-area components, axle-beam trumpets and associated assemblies.
- Differential and brake-pack work – differential-group dismantling and assembly, pinion-group setting procedures, brake packs and differential-housing work.
- Brake system service – brake-system bleeding, hydraulic-pressure dissipation procedures and hydraulic-level checks.
- Special tools – axle and steering special-tool references for bearing, bush, seal, pinion and preload-related operations.
- Engine section – engine description and data, plus removal and installation procedures with the engine pod fitted and with the pod left on the machine.
- Transmission description and specifications – torque converter, Dana T12000 transmission and drop-box arrangement, gearbox identification and transmission technical data.
- Powershift and APC controls – gear selection with APC, non-APC option information, speed-sensor testing, solenoid arrangement, controller connections, display menus and fault-code information.
- Transmission electrical checks – lever-to-controller connections, pin layouts, display-input tests and APC output testing.
- Gearbox operation and hydraulic circuits – gearbox power flow, gear and clutch layout, clutch function, solenoid/gear-selection tables and hydraulic selection plans.
- Gear-specific transmission schematics – neutral, first through sixth gears and reverse hydraulic schematics, together with gearbox-pump and accumulator-damping-valve information.
- Transmission testing and troubleshooting – test-port locations, pressure checks, stall tests, mechanical, electrical and hydraulic checks, and fault guidance for clutch pressure, charge-pump output, overheating, converter noise and lack of power.
- Transmission overhaul – removal and installation, transmission dismantling, clutch dismantling and assembly, regulator and modulating-valve work, converter housing and electric-control assembly.
- Boom system – boom description and operation, maintenance, boom removal and installation, hydraulic cylinders, boom tray cassette, inner boom and wear-pad replacement procedures.
- Chassis and operator’s cab – chassis description, cab removal and installation, fuel-tank removal and installation, and post-repair functional checks.
- Heating and air-conditioning equipment – blower motor, heater coil, evaporator, receiver-drier, condenser, axial fan/relay and compressor removal and installation procedures. Compressor information distinguishes machines up to serial number 51200471 and from serial number 51200472.
- Technical data – machine dimensions, tyres and supporting specification information for the covered Targo handlers.
MODELS COVERED
- CLAAS Targo K50 telescopic handler
- CLAAS Targo K60 telescopic handler
- CLAAS Targo K70 telescopic handler
The documented coverage is for machines from serial number 51200011 to 51200727, including Targo K50 machines from K5D00100, Targo K60 machines from K6D00100 and Targo K70 machines from K7D00100.
MANUAL DETAILS
Manufacturer: Claas
Models Covered: Targo K50, Targo K60 and Targo K70
Machine Type: Telescopic handler
Manual Type: Workshop repair manual
Format: Digital PDF
Publication Number: 349865.0
Publication Date: August 2003
Page Count: 252 pages
Serial Coverage: Machines 51200011 to 51200727; K50 from K5D00100, K60 from K6D00100 and K70 from K7D00100.
The Claas Targo K50 Workshop Manual includes the repair information needed for major mechanical, hydraulic-control and transmission-related work, with procedures and technical checks presented by machine system.
WHAT HAPPENS AFTER PURCHASE?
After purchase you will instantly receive our download information file by email. Your manual will then be manually checked and sent to the email address used during checkout, usually within minutes and normally within 1 hour.
WHY BUY FROM AGRIMANUAL?
- Established in 1995 supplying technical manuals
- Digital PDF manuals for agricultural and construction machinery
- Large archive including rare and discontinued manuals
- Worldwide service
- Manual orders checked before delivery
Reviews
There are no reviews yet.